Home and Interior

The mounting foam wash with hand, doors and clothes? What if the foam has dried up?

Content

Polyurethane foam - a popular product among builders,especially conductive installation of plastic windows. It's household products, packaged in an aerosol can and perfectly fills the cavity. It has excellent adhesive qualities, so topical issue among employees than the mounting foam wash with it.


The wash assembly foam?

The wash assembly foam

At the core are polyurethane foam -gas-filled plastics. When you work with it, anyone who forgot to wear gloves on itself felt, how great its adhesives and adhesive quality. And as practice shows, everyone knows the safety rules, but often do not use them. Thus, the foam on his hands - what to do in the first place?

After the foam contact with the exposed surface of the handsyou need to immediately wash it with a special solution or liquid atsetonsoderzhaschey. You can also moisten the cloth with solvent and wipe the contaminated area of ​​the skin, and then wash your hands with soap and water, while sparing no water.

However, it happens sometimes that neither acetone norwashing the foam was not at that moment at hand. In this case, you can borrow from women to remove fresh foam from hands nail polish remover. In addition, use of any other available solvent for lacquers and paints up to gasoline. It should be mandatory hand washing after use.

If there is nothing of the dissolving liquid,should wait until the foam has dried, after which it is quite easily removed by mechanical action. Note: fresh, just hit the foam on your hands or other body parts in any case can not be cleaned off with a cloth. This can only make matters worse - smeared with a thin film and frozen foam will require long-term clean-up procedures.

See also:

The cured foam to wash? In this case, the mechanical effect will by scraping. should be used for this purpose:

  • own nails;
  • fine-grained sandpaper;
  • brush with coarse bristles;
  • pieces of the abrasive wheel;
  • pumice stone;
  • blade or razor blades, but it requires careful and cautious to avoid cuts.

To improve productivity and facilitatefoam cleaning process with hand as an adjuvant can enable hot water and warmed vegetable oil. Hold in these liquids half an hour hand, it is possible to achieve a softening of the epithelium and scraping it easier to be separated together with the foam, thus arranging artificial skin renewal process. By the way, if nothing is done, over time the foam away with it, along with the dead skin layer, but this option is suitable for those who are worried about their appearance.

The people widespread use ofdrug, which differs a great ability to penetrate the skin of the membrane - "Dimexidum". It acts as a solvent on the foam. However, the individuality of the organism reactions to medications has not been canceled, and the smell of him very much zaboristy.

Clear the foam from the doors and windows

Clear the foam from the doors and windows

In addition to the protection of their own hands, for that matter, andthe whole body of the foam hit, should also take care of the protection of surfaces. If contact could not be avoided, the knowledge, than to wash the mounting foam doors, floors, windows, will not be superfluous.

The first step is to determine the importance ofmanufacturing and coating material, such as doors. If the preservation of coatings and irrelevant material allows, we can cut most of it with a knife or blade, and then a scraper and a brush to clean off the remaining foam.

When the coating has a value necessarysolvent or a special washing liquid. First try to remove the foam on inconspicuous area. The solvent can act as a negative to the foam, and the paint, varnish, the surface itself. You can also use the drug already known to us from the medicine cabinet - "Dimexidum".

What if the foam onto your clothing?

Before you find out what to launder assembly foamwith clothing, it should be noted that if the pre-think about the potential problems and to put before the works of the things that do not mind, the relevance of the issue will tend to zero. If the clothes soiled, but it is a pity to throw, you must perform these steps:

  1. Remove the bulk of the foam, cut her with a knife.
  2. Use of available solvent, check its effect on the fabric. The purpose of this - to prevent on-site spots get damaged foam material.
  3. With a negative impact on the fabric treated with solvents or special liquid spot without resorting to rubbing, and remove the foam.
  4. After cleansing the clothes should be washed - so you can minimize the effect of the solvent on the fabric structure.

To summarize, we should once again draw the attention ofon preventive methods. It is better to provide the effect of something, than to wrestle with how to fix the consequences. Protection of hands, eyes and hair - measures necessary personal safety. And the use of suitable work clothes will allow you to save on buying a new one instead of spoiled in the event of failure of the last cleaning.

See also:

Protection work surfaces and placespossible ingress of foam tape, paper tape construction will help to avoid unnecessary headaches. Knowledge of the methods of cleaning and flushing foam allow advance to worry about acquiring the necessary and effective action means the use of which may be required at any time. I wish you success!

Like this? Share it in social. NETWORKS

Leave a Comment